Related Products

Denntal High-Speed LED Handpiece L-A 110218

Standard Configuration

High-Performance High-Speed Handpiece

Key Features

Durable Optical Fiber: Glass-hard optical fiber for superior illumination.

Efficient Design: Cost-effective open movement for easy bearing replacement.

Enhanced Lighting: Unique lamp cap design for easy bulb replacement; shatter-resistant bulbs.

Optimal Cooling: Three-point spray ensures all-around cooling.

Quick Connection: User-friendly, fast installation.

Copper Body: Durable and resistant to wear.

Specifications

Air Pressure: 0.25 MPa – 0.30 MPa

Speed Range: 320,000 – 420,000 RPM

Bur Size: φ1.593mm – φ1.598mm

Noise Level: ≤63 dB

Interface: ISO-E international standard

Featured of Dental Highspeed LED HandPiece L-A 110218

Check Our All Products

Bright & Natural Illumination

Equipped with a built-in generator and high-quality LED light, this handpiece delivers natural, well-focused illumination, enhancing visibility in the treatment area for precise dental procedures.

High-Temperature Sterilization

The handpiece is fully autoclavable up to 135°C, allowing for repeated high-temperature and high-pressure sterilization, ensuring optimal hygiene and patient safety by preventing cross-contamination.

Advanced Cooling System

Featuring a three-point water spray system, this handpiece ensures superior atomization and comprehensive cooling, effectively preventing overheating of tooth structures and improving procedural efficiency.

Universal Compatibility

Designed to fit both 2-hole and 4-hole dental unit connections worldwide, eliminating the need for additional modifications or wiring replacements, ensuring seamless integration into any clinic setup.

Dental Handpiece Different Connecting Type:

Check Our All Products

Normal handpiece :how to match tightly handpieceair tube and chair connector

Check Our All Products

Dental High-Speed Handpiece Cartridge Disassembly and Installation Guide

Check Our All Products

Disassembly:

1:Align the wrench cap position with your left thumb on the cap.

2:Turn counterclockwise to open the cap.

3:Use your index finger to gently move out the cartridge.

Installation:

1:Ensure that the cap has a spring pad in place.

2:Position the head of the cartridge in the cap (as shown in the image), and with the hand holding the bur, ensure it fits smoothly.

3:Turn the cap clockwise a few times, then tighten using the wrench.

Installation Guide

This simple process ensures easy and secure cartridge replacement for optimal handpiece performance.

Changing Burs for High-Speed Handpiece

Check Our All Products

1: With your right hand, hold your thumbs up and press the gland to open the chuck.

2: Use your left hand to carefully remove the bur.

3: To load a new bur, follow the same steps as above, ensuring the bur is properly aligned with the shaft hole.

This ensures secure and accurate placement of the bur for efficient use during procedures.

Dental High-Speed Handpiece Maintenance

1: Apply special lubricating oil before and after each use.

2: After use, blow air through the head and bur transfer position to clean them. Tilt the handpiece at a 45-degree angle to avoid blowing debris inside the head.

3: Blow air through the two small tubes at the tail to remove residual moisture and debris.

4: Once a month, remove the cartridge, and clean any foreign bodies from the cavity in the head and cap.

Proper maintenance helps ensure the longevity and optimal performance of your handpiece.

Dental High-Speed Handpiece Exception Occurs And Solution

  • Problem:Noisy
  • Reason : 1: Bearing damage; 2: Bur curved; 3: cap without cushion
  • Solution: 1: Change bearing or bur; 2: Put new washer

  • Problem: Light slowly or does not ligh
  • Reason : 1: Poor water quality to block the water hole 2: Atomization gas too much to hold back the water
  • Solution: 1: Use a silver needle to drill the bearing hole (as the picture shows)
    2: The ato water or no wamization will be small much

  • Problem: Poor power
  • Reason : 1.Foreign body to block the head into the hole ; 2.Chair exhaust pipe plug exhaust is not suitable
  • Solution: 1.using the file into the air hole; 2.Vent the air to the vent holesuitable

  • Problem: Can not catch the bur
  • Reason : 1.Bur is not standard; 2.Spindle is damaged
  • Solution: 1.Change standard bur; 2.Change spindle

  • Problem: Leakage
  • Reason : 1.Connection is not tightening; 2.O-ring is damaged
  • Solution: 1.Connect with the Chair twist; 2.Change plug o-ring

  • Problem: Connections twist tightly
    Reason : The Chair joints damage
    Solution: Change chair Connector

What Sets Lavender Dental Apart

Lavender Dental is a trusted name in the dental industry, renowned for providing high-quality, reliable dental equipment to professionals worldwide. Our brand stands out for its commitment to excellence, innovative solutions, and dedication to customer satisfaction. Whether you're outfitting a new dental practice or upgrading your existing equipment, Lavender Dental is your go-to partner for superior products and unmatched expertise.

Recently Viewed Products