Dental Chair Machine Operation Control Panel
Every long press on the button shall trigger the patient chair to move according to every respective arrow indication; the patient chair shall stop moving if the button is released:
“UP"Dental chair, upwards
"DOWN"Dental chair, downwards
"LEFT"Dental chair, tilt backwards
"RIGHT"Dental chair, tilt forwards
Press the “LP” key one time, the dental chair backrest shall move to the most front position so as to facilitate the patient to spit and clean mouth; press the button again, the dental chair backrest shall move back to its previous position.
Notes:
In the running course of the dental chair backrest, if other function keys are pressed, the functions triggered by such key shall stop automatically.
Press the “ Icon of mouth water supply ” key one time, the mouth wash supply shall stop after the setting time is up; during the mouth wash supply period, every press on this key shall stop water supply.
Press the “SET button, pilot lamp is shining ,press the “Icon of spittoon flush " key fourth times the spittoon flush, press the key "SET” again, the pilot lamp is extinguish, then finishing sett ing ,the whole flowing process is set about 15 seconds.Repeatthe process, press one time “Icon of spittoon flush " to set 30 minutes for whole flowing process, twice for 60 minutes,three times for all times, fifth times is cycling as the firsttime.
Press the“Heating ” key one time, the constant-temperature water heater shall be started to heat water to a temperature of 40℃±5℃; if the water temperature reduces, the water heater shall start automatically (the indicator lamp shall flash in the heating process; the indicator lamp shall be always on after the setting value is reached); every press on the key again shall stop the water heater (the indicator lamp shall be off).
Notes:
The hot water shall only be supplied for mouth cleaning and 3-way syringe (connect the open the water supply
before using the water heater so as to prevent it from burning without water and causing short circuit).
Press the “Icon of Film viewer ” key one time, the power supply of the film viewer shall be connected; press the key again, the power supply of the film viewer shall be disconnected.
Notes:
There is a power switch on the film viewer.
Press the key "Icon of the light"one time, the power supply of the operating light shall be connected; press the key again, the power supply of the operating light shall be disconnected.
Notes:
There is a power switch on operating light.
Press the“PRG” key to change the program, in order to change from A to B; press again to change from B to C;if you press“PRG” again, the program changes from C to A;User can customize 0-9 memory positions for the dental chair.( Depending on function of the device.) Every press on the memory key shall trigger the corresponding indicator lighten and the corresponding memory procedure; in such case the dental chair shall move to the corresponding memory position.As for the customized setting, please refer to“(10) Setting Key".
Notes:
In the running course of the dental chair, if other function keys are pressed, the functions triggered by such key shall stop automatically.
Press the“RESET" key one time, the dental chair shall lower minimally and leans forward.
Notes:
In running dental chair, if other function keys are pressed, the functions triggered by such key shall stop automatically.
I) Set mouth water supply time
Step 1: Press the“SET” key one time, the indicator shall be on;
Step 2: Keep on pressing the “” key till the desired water volume is reached;
Step 3: Press the“SET” key one time, the indicator shall be off. Finish setting.
Notes:
The setting procedure limits only the water supply time; however the huge change in water pressure
may cause change in water supply volume; in this case please re-set accordingly.
II)Set dental chair memory positioning
Step1: Press the“SET" key one time, the indicator shall be on;
Step 2: Keep on pressing the“UP" or the"DOWN"key (press one of them only, or both are not pressed) till
the dental chair moves to the presetting height;
Step 3: Keep on pressing the "LEFT"or the“RIGHT” key (press one of them only, or both are not pressed) till the
dental chair backrest moves to the presetting angle;
Step 4: Press Key A, B or C, and then press any key of the 3 memory positions;
Step5: Press the“SET" key, the indicator shall be off and the setting is thence finished; till now the presetting
seat position has been stored in the corresponding memory key.
